How to Use a Wax Seal Stamp: Wax, Tools and Tips for a Clean Impression

A wax seal turns a letter, invitation or parcel into something worth keeping. Making a good impression is simple once the wax, the tools and the size of the stamp are matched to one another. This guide covers what sealing wax is made of, which tools suit each seal size, and how to make a clean, sharp impression.

What medieval sealing wax was made from

The wax hanging from medieval charters was mostly beeswax, softened and strengthened with a resin such as Venice turpentine, a resinous extract of the European larch. The earliest seals were left in the natural colour of the wax. Later, pigments were added: vermilion for red, and verdigris for green. Pure beeswax tends to crack as it ages, and the resin helped the wax hold a crisp impression and survive for centuries.

Vermilion is a brilliant red pigment made from mercury sulphide, either ground from the natural mineral cinnabar or made artificially by combining mercury and sulphur. It was costly and highly prized, and red wax became closely associated with important and official documents. Being a mercury compound, it is also toxic.

Verdigris is a green pigment made from copper. It is the same blue-green crust that forms naturally on old copper, brass and bronze, and medieval craftsmen produced it deliberately by exposing copper plates to the fumes of vinegar. Mixed into wax, it gave the green seals found on many medieval charters.

From the sixteenth century, sealing wax was increasingly made with shellac, resin, chalk and pigment, often with no beeswax at all, producing the hard, brittle sticks associated with sealed letters of later centuries.

Modern sealing wax

Most sealing wax sold today is a polymer blend. It melts easily, comes in a wide range of colours, including metallics, and stays slightly flexible once set, so a seal is far less likely to crack or snap off in the post than traditional brittle wax. It is sold as sticks for glue guns, as traditional sticks with or without a wick, and as beads or granules for melting. All are widely available online.

Choosing tools for the size of your seal

  • 50mm seals need a generous pool of wax. A full-size glue gun with large wax sticks is the easiest way to lay down enough wax quickly and evenly. If using wax beads, allow roughly 10 beads for each 50mm seal.
  • 30mm seals work well with a mini glue gun and small wax sticks, or with wax beads melted in a wax spoon.
  • 20mm seals need only a little wax, so a wax spoon or a mini glue gun is ideal.

As a rough guide, the pool of wax should be a little wider than the face of the stamp, so the impression has a neat border.

Melting wax beads

Wax beads can be melted in a traditional wax spoon held over a tealight, but a dedicated spoon is not essential. A small cast iron pan works well, especially for larger batches, as it holds heat evenly. Even the empty metal cup from a used tealight candle makes a handy disposable melting pot.

Whatever is used, warm the wax gently. It should melt slowly into a smooth, glossy liquid and should never smoke. Smoking means the wax is burning rather than melting, which spoils the colour and gives off fumes. If it starts to smoke, take it off the heat straight away. Never leave melting wax unattended.

Making the impression, step by step

  1. Lay the paper or envelope on a flat, heat-resistant surface. A silicone mat makes practice easy, as finished seals peel straight off it.
  2. Melt the wax and pour or squeeze it into a pool slightly larger than the stamp. Give a few seconds for the surface to lose its glossy, runny look.
  3. Press the brass stamp straight down into the wax with steady, even pressure. Avoid rocking it.
  4. Hold it in place for around 10 to 20 seconds while the wax firms up.
  5. Lift the stamp straight up. If it sticks, wait a little longer before trying again.

Tips for a crisp seal

  • Cool the stamp between seals. A warm stamp blurs fine detail. Resting the brass head on a cold surface or an ice pack for a moment between impressions keeps the detail sharp.
  • Stir in a second colour. Swirling two colours together in the pool before stamping gives a marbled finish.
  • Make seals in advance. Seals can be made in batches on a silicone mat, baking paper, aluminium foil or a smooth pane of glass, all of which let the cooled wax lift off cleanly. They can then be fixed to invitations later with a dab of strong glue or a glue dot.
  • Keep the stamp clean. Pick any wax out of the design with a soft brush or wooden cocktail stick, never a metal point, and store the stamp in its velvet pouch.

NobleSeals stamps

Every NobleSeals stamp has a solid brass head and comes with a wooden handle and a velvet pouch. Historical designs, from royal Great Seals to pirate flags, are available in the historical collection.

Browse the historical collection

Further reading

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.